Military Standard 810 (MIL-STD-810) Training
DATE: October 17-20, 2022 8:00 am – 4:00 pm
LOCATION: NTS Boxborough, MA
TEACHER: Steve Brenner
CONTACT: (805) 456-4274
This 4-day Military Standard 810 (MIL-STD 810) training focuses on the purpose of each test, the equipment required to perform each test, and the methodology to correctly apply the specified test environments. This class is applicable to ANY testing done to Environmental test standards including DO-160, IEC specifications, and all other documents which provide test methodology for environmental testing. The test methods explained and taught in this class apply to environmental testing of ANY equipment whether it is intended for military/aerospace, commercial, or consumer use.
Vibration and Shock methods are covered together. We overview Sine and Random Vibration, also classical waveform shock testing, drop testing and Shock Response Spectrum Testing. We include instrumentation, vibration equipment, control systems and fixture design.
We discuss each climatic test individually, focusing on requirements, origination, equipment required, test methodology and understanding of results.
Class members will tour a lab that daily performs the full spectrum of 810H tests.
The lab visit will include a demonstration of the vibration test equipment and test techniques discussed in class. An instrumented resonant structure is excited first with slowly sweeping constant acceleration sine vibration. As the frequency increases the observers will see directly the decrease in displacement. The sine vibration demonstration will be followed by an all-frequencies-simultaneous random vibration. Responses are compared.
500.6 Low Pressure (Altitude)
501.7 High Temperature
502.7 Low Temperature
503.7 Temperature Shock
504.3 Contamination by Fluids
505.7 Solar Radiation (Sunshine)
509.7 Salt Fog
510.7 Sand and Dust
511.7 Explosive Atmosphere
515.8 Acoustic Noise
518.2 Acidic Atmosphere
519.8 Gunfire Shock
520.5 Combined Environments
521.4 Icing/Freezing Rain
522.4 Ballistic Shock
524.1 Freeze / Thaw
525.2 Time Waveform Replication
526.2 Rail Impact
528.1 Mechanical Vibrations of Shipboard Equipment (Type I – Environmental and Type II – Internally Excited)
Classroom discussion is supported by projected visuals and video clips. Commencing with a review of basic vibrations, we will explore vibration measurements and analysis. We’ll compare sinusoidal vs. random vibration testing systems, specifications, standards and procedures. We will emphasize vibration and shock test fixture design, fabrication, experimental evaluation and usage. We will study shock measurement, shock response spectrum (SRS) and shock testing.
Climatic testing will be looked at in great detail, emphasizing required equipment and instrumentation, correct interpretation of specifications and hints to ensure that the tests are brought to a successful conclusion.
In addition to the detailed observations of chambers in the Lab, numerous photographs of general purpose and special purpose chambers are provided such as Solar Radiation and Rain. Along with “catalog photos” of chambers, the instructor shows unpublished factory in-construction via photos of chambers.
The course emphasizes topics you will use immediately. Suppliers to the military services protectively install commercial-off-the-shelf (COTS) equipment in our flight and land vehicles and in shipboard locations where vibration and shock can be severe. We laboratory test the protected equipment (1) to assure maximum equipment survival and possible combat, also (2) to meet commercial test standards, IEC documents, military standards such as STANAG or MIL-STD-810H, DO-160, etc. Few if any engineering schools teach about such protection or such testing. Hence this specialized course.
Comparison of 810 Revisions
810H is the latest revision. MIL-STD-810 has been revised roughly every 8 years since it was introduced in 1962. Some of the earlier revisions are occasionally cited in procurement contracts. This course covers ALL the test methods of the latest revision. The last method numbers are found in the final column of this available-for-download PDF file. The instructor will also discusses commonly specified older legacy methods.
After this Military Standard 810 (MIL-STD 810) training, you will be able to:
- Specify and perform vibration, shock and climatic tests
- evaluate and select equipment to perform testing
- convert field measured data into a test program,
- interpret vibration and shock test requirements and results,
- supervise vibration, shock and climatic tests,
- specify and experimentally evaluate vibration and shock test fixtures
When you visit a test lab or review a test program, you will understand the requirements and execution of dynamics and climatics tests. You will be able to ask meaningful questions and understand laboratory personnel responses.
This Military Standard 810 (MIL-STD 810) training is aimed at people who need to perform, witness or specify environmental testing in accordance with Military Standard 810 (or any other similar environmental test standard)
It covers all of the Dynamic and Climatic tests described in MIL-STD-810. Are you saying to yourself “I need practical knowledge about MIL-STD-810 testing because my work requirements are:
- My title may be mechanical engineer, mechanical designer or packaging engineer. I design (ruggedize) products that must pass MIL-STD-810 testing. I design products to dynamic and climatic requirements, which I don’t fully understand. Then I send a prototype to our lab for testing. I really don’t understand what our lab does. I’d better find out.
- I write contracts for or specifications procuring military equipment. I need to understand the requirements of MIL-STD-810. How do I ensure that potential contractors understand and will correctly implement the requirements?
- I need to witness and approve testing that is specified to be performed “in accordance with MIL-STD-810”. How do I know if the test equipment proposed is capable of doing the job? How do I know if the data I am given is accurate?
- I work in an environmental test lab. We need to perform tests “in accordance with MIL-STD-810”. How do we perform these tests? How do we interpret the requirements? What in heck is g2/Hz?
- I have been tasked with procuring equipment to perform tests “in accordance with MIL-STD-810”. How do I know I am specifying the right shakers, shock test machines, chambers?
If you thought, “aha – that’s what I’m supposed to do” to any of the job descriptions listed above, then this course is intended for you. It will help you move up your own “learning curve.”
A smaller group, for whom ERI also intends this education: supervisors of any of the above listed activities. Perhaps you were thrust into this responsibility without adequate training. Maybe your predecessor had no opportunity to alert you to potential difficulties. You certainly need to know what your people are talking about. Possibly you had no formal training for your present responsibilities. You need to explain your department’s activities to your superiors in the technically correct language. Perhaps you need to decide between “in house” and “outside” testing.
Introduction to Military Standard testing – Dynamics
- Introduction to classical sinusoidal vibration
- Resonance effects
- Acceleration and force measurement
- Electrohydraulic shaker systems
- Electrodynamic shaker systems
- Sine vibration testing
- Random vibration testing
- Attaching test articles to shakers (fixture design, fabrication and usage)
- Shock testing
- Vibration lab demonstration
Introduction to Military Standard testing – Climatics
- Temperature testing
- Temperature shock
- Rapid decompression/explosives
- Combined environments
- Solar radiation
- Salt fog
- Sand & Dust
- Explosive atmosphere
Climatics lab demonstration
Reporting on and certifying test results
Course summary; optional final examination; award of certificates
Text Material Instructor Steve Brenner has prepared a highly valuable set of downloadable PDF files. On each of the 20 climatic test methods, Steve defines terms, provides such commentaries as “What can go wrong during this test?” He gives the purposes of that test, suggests products on which that test is appropriate and identifies the service environment being simulated. He explains what weaknesses that test can reveal. He identifies what is being controlled during that test and how that control is affected. He deals with the possibility of accelerating that test.
Because few of those just entering climatic testing have seen very many (if any) climatic test chambers, Steve provides numerous pictures of general purpose and special purpose chambers, such as Solar Radiation and Rain. Along with “catalog photos” of chambers, Steve shows unpublished factory in-construction via photos of chambers.
Random Vibration & Shock Test Books Each participant also receives a copy of Wayne Tustin’s text ‘A minimal-mathematics Introduction to the Fundamentals of Random Vibration and Shock Testing, HALT, ESS & HASS, also Measurements, Analysis & Calibration’. The text is provided to each student as an “e-book” in .epub format. The text includes many video clips pertaining to sine and random vibration and shock behavior and testing.
To contact Steve send an email to email@example.com
Steve Brenner has been working in the field of environmental simulation and reliability testing for over 35 years. Commencing about 20 years ago, he became an independent consultant, and is one of ERI’s most sought-after teachers of short courses.
Beginning in the late sixties with reliability and design verification testing on the Lunar Module, the Space Shuttle in the eighties, to semiconductor manufacturing equipment in the nineties, Mr. Brenner has always been involved with the latest techniques for verifying equipment integrity through testing.
Mr. Brenner began his career as an Environmental test engineer with Grumman Aerospace Corporation in New York, worked as design verification and reliability engineer for the Air Force, an Environmental Test Engineer for Lockheed Missiles and Space company, and spent 18 years with Kaiser Electronics in San Jose, where he managed the Environmental Test Lab and was involved with the design of hardware intended for severe environments.
Mr. Brenner has been working as a consultant in the reliability testing field since 1996. His client base includes American and European companies with products:
- Automated test equipment
- Airborne displays
- Network equipment
- Medical equipment
- Semiconductor manufacturing equipment
- Aircraft instrumentation
- Ruggedized commercial electronic products (COTS)
- Fiber Optics components and systems
- Theme Park Rides
Mr. Brenner’s experience includes Military Standard 810 testing, the entire range of climatic and dynamic testing, including HALT, HASS and long term reliability testing. He teaches several ERI courses each year, USA and abroad. In 2006 he and Wayne Tustin co-authored “Where to place the vibration test control accelerometer?”, which is available upon request.
Equipment Reliability Institute (ERI) offers specialized technical short course training in Shock and Vibration Testing, Climatics Testing and MIL-STD-810 Testing. Testing classes are applicable to all commercial, military and aerospace requirements.
Fundamentals of Random Vibration and Shock Testing @ Element | NTS Labs Newark, CA November 7-9, 2023
Military Standard 810 (MIL-STD 810) @ Element Materials Technology Huntsville, AL December 4-7, 2023